6205-2RSH/C3, 6205-2RSR-C3, 6205 DDU C3 – three designations, essentially the same bearing. Anyone wanting to replace a deep groove ball bearing quickly stumbles over the letters and numbers following the actual bearing number. These suffix codes describe sealing, internal clearance, precision, and the cage – and unfortunately, each manufacturer partly uses their own abbreviations. In this article, we show how a bearing designation is structured and what the various codes mean.

1. Structure of a Bearing Designation

The designation of rolling bearings is regulated in DIN 623-1 and ISO 15 respectively. Using W 6205-2RS1/C3 as an example:

Part Meaning
W Prefix – here: stainless steel
6 Bearing type – 6 = deep groove ball bearing, single row
2 Dimension series (diameter and width series)
05 Bore code – 05 × 5 = 25 mm inner diameter
-2RS1 Suffix: Sealing (rubber seal on both sides)
/C3 Suffix: Internal clearance (greater than normal)
  • The basic designation (bearing type + dimension series + bore, e.g., 6205) is the same for all manufacturers – a 6205 always has the same dimensions.
  • Bore code: 00 = 10 mm, 01 = 12 mm, 02 = 15 mm, 03 = 17 mm, from 04 onward the code applies × 5. For miniature bearings, the last digit is directly the bore diameter (608 = 8 mm), and special dimensions are written with a slash (e.g., 60/28 = 28 mm).
  • The suffix codes, on the other hand, are partly manufacturer-specific – a closer look is worthwhile here.
  • Spellings vary: 6204-2RSH/C3, 6204 2RS C3, 6204-2RS-C3, or 6204 2RSC3 all mean the same thing. Spaces, hyphens, and slashes have no independent meaning.

2. Sealing: Open, ZZ, or 2RS?

There are three common designs for deep groove ball bearings:

  • Open – without seals, lowest friction running, but unprotected. Mostly used in lubricated gearboxes.
  • ZZ – two sheet steel shielding discs, non-contact. Very high speeds possible, protects against coarse dirt, but not against water.
  • 2RS – two rubbing rubber seals (NBR). Sealed against dust, splash water, and grease leakage, but with a slightly lower limiting speed.

This is what these designs are called by individual manufacturers:

Design SKF FAG / Schaeffler NSK NTN Koyo NACHI Other
Open – – – – – – –
ZZ
2 shield discs
2Z 2Z ZZ ZZ ZZ ZZ, ZZE ZZ, 2Z
2RS
2 rubber seals
2RSH, 2RS1 2RSR, 2HRS DDU LLU 2RS, 2RK 2NSL, 2NSE 2RS

Bearings sealed on one side bear the mark without the preceding "2" or with the letter only once: Z, RS, RSH/RS1 (SKF), RSR (FAG), DU (NSK), LU (NTN).

SKF 2RSH or 2RS1? Both are NBR seals rubbing on both sides. SKF primarily uses 2RSH for smaller bearings in the 60, 62, and 63 series, and 2RS1 for larger bearings, the thin 618/619 series, and stainless steel bearings. For replacement, both are equivalent to a 2RS bearing.

Caution: Risk of Confusion

Not every rubber seal is a 2RS seal. The following codes look similar but mean something different:

Code Manufacturer Meaning
2RZ SKF, FAG Rubber seal, but non-contact – behavior similar to ZZ, not as tightly sealed as 2RS
2BRS FAG Generation C Non-contact labyrinth seal
VV / LLB NSK / NTN Non-contact rubber seal
2RSL SKF Low-friction rubbing seal (2RS variant)
2ELS FAG Generation C Rubbing seal with exceptionally high sealing effect (2RS variant)
2RS2, 2RSH2, 2CS2 SKF Seal made of FKM (Viton) – heat-resistant special design
N, NR, ZNR, 2ZNR SKF et al. Snap ring groove or snap ring on the outer ring – different installation situation

Sealed bearings are filled with lifetime lubrication and designed for a temperature range of approx. –30 °C to +110/+120 °C.

3. Internal Clearance: CN or C3?

Bearing internal clearance is the radial play between the inner ring, balls, and outer ring. It is standardized and designated identically across all manufacturers:

Code Meaning
CN (usually omitted) Normal clearance – standard for most applications
C3 Greater than normal – e.g., for electric motors, in case of thermal expansion, or firm press fits
C2 Smaller than normal
C4, C5 Even greater than C3
CM Closely tolerated bearing clearance specifically for electric motors (Schaeffler, NSK)

Good to know: If there is no clearance abbreviation after the bearing number, it is normal clearance (CN). At SKF, the bearing clearance is usually placed after a slash (6204-2RSH/C3). The manufacturer SNR writes C3 as J30. Combined codes group precision and clearance together: P63 = P6 + C3, P43 = P4 + C3.

Tip: Always replace a bearing with the same internal clearance as the original. If C3 is marked on the old bearing, the new one should also be a C3 bearing.

4. Precision (Tolerance Class)

ISO / DIN ABEC (USA) Meaning
P0 / PN (without sign) ABEC 1 Normal tolerance – standard
P6 ABEC 3 Increased precision (e.g., standard in FAG Generation C)
P5 ABEC 5 High precision
P4 / P2 ABEC 7 / 9 Precision and spindle bearings

5. Cage

For deep groove ball bearings in common sizes, a sheet steel cage is standard and is generally not specified. Other cage designs can be recognized by these abbreviations:

Cage SKF FAG NSK NTN Other
Sheet steel (standard) – – – J –
Solid brass M, MA, MB M, MA, MB M L1 M
Sheet brass – Y – – –
Polyamide (PA66) TN9 TVH TNG, T85 T2 TN, G15

6. Prefix

Characters can also appear before the bearing number:

  • W (SKF), S6…, SS, X- – stainless steel, e.g., W 6205-2RS1. Do not confuse with the standard bearing made of rolling bearing steel!
  • D/W (SKF) – stainless, inch dimensions
  • R (FAG) – single ring (inner or outer ring only)

7. Further Characters You Might Encounter

Code Meaning
C (FAG) Generation C – noise- and friction-optimized, precision P6
E (SKF) Optimized internal design, identical dimensions
A, B, AA, D Modified internal design
X Main dimensions deviate from ISO – dimensions must be checked
JEM (SKF) Design for electric motors with bearing clearance C3 and special grease
GJN, HT, LT, MT33, MT47, LHT23, WT Grease type (SKF)
VT143, VT378 Special grease (high pressure or food grade)
VA947, VP311 SKF Food Line – blue seal, H1 grease for the food industry
S0, S1, S2 Heat stabilized up to 150 / 200 / 250 °C
HC5 Ceramic balls (hybrid bearing)
Z1V1 … Z4V4 Noise or vibration class – not a shielding disc!
DB, DF, DT Paired bearing set (O, X, or tandem arrangement)

8. Examples for Decoding

Designation Meaning
SKF 6204-2RSH/C3 Deep groove ball bearing 6204, rubber seal on both sides (2RS), internal clearance C3
FAG 6204-2RSR-C3 The same bearing from FAG
NSK 6204DDUC3 The same bearing from NSK
SKF 6009-2Z/C3 Deep groove ball bearing 6009, shield discs on both sides (ZZ), internal clearance C3
SKF 6207/C3 Deep groove ball bearing 6207, open, internal clearance C3
SKF 61806-2RS1 Thin section bearing 61806 (= 6806), 2RS, normal clearance
SKF 61806-2RZ As above, but with a non-contact seal – not 2RS!
SKF W 6205-2RS1 Deep groove ball bearing 6205 made of stainless steel, 2RS

The Most Important Points in Brief

  • Bearing number and internal clearance are standardized – a 6205 C3 has the same size and the same clearance with every manufacturer.
  • Sealing and cage are designated differently depending on the manufacturer.
  • SKF: 2RS = 2RSH or 2RS1, ZZ = 2Z. FAG: 2RS = 2RSR or 2HRS, ZZ = 2Z. NSK: 2RS = DDU. NTN: 2RS = LLU.
  • 2RZ and 2BRS are not 2RS bearings – the seal is non-contact.
  • Normal clearance (CN) is usually not specified, C3 stands behind a slash at SKF.
  • A W before the number means stainless steel at SKF.

Unsure which bearing you need? Send us the designation of your old bearing – we will gladly help you with the selection.

Caution created to the best of our knowledge! Mistakes can happen to us too
AI-supported